1. Lightweight shelf:

Using cold-rolled steel plate, stamping forming, easy to disassemble, flexible combination. Strong transformation. Be able to meet the customer's placement requirements to increase or decrease the number of layers in order to achieve the best results. The column adopts angle steel, and the height of the laminate can be adjusted up and down to 50mm.

Structure: laminate, support, column angle sleeve, column, fixed up and down.
 

2. Medium type A shelf:

Easy to assemble and disassemble, beautiful and generous in appearance, suitable for manual storage of goods, the carrying capacity is generally 200-350KG/layer, which can meet the needs of most customers, and the laminate can be adjusted at an upper and lower intercept of 50mm.

Structure: no bolt connection, by the layer plate, safety buckle, beam, column, angle sleeve, hanging piece, fixed up and down.

3. Medium B type shelf:

It is also suitable for manual access to goods. Compared with A- type shelves, as the laminate is changed to the width direction, the bearing capacity is greatly improved. It is widely used in various industries, with low cost, safety and reliability, convenient assembly and disassembly, and can be used alone. It can also be freely arranged into various arrangement modes. The bearing capacity of each layer is about 800KG, and the intercept is generally adjusted at 50mm.
Structure: upright post, cross beam, diagonal brace, cross brace, laminate, foot, side plate, back net, back plate effective parts can be added as appropriate, and each layer needs a crossbeam.

4. Beam type shelf:

A common kind of shelf, providing 100 of accessibility, and has good picking efficiency, but this kind of shelf has low access density, needs more roadways, usually uses 3-5 layers, shelf height limit is generally below 10M, suitable for general forklift access, can be adjusted and combined at will, is safe and simple, economical in cost, and is not limited by the order of goods entering and leaving the warehouse. According to the width of the shelf access roadway, it can be divided into traditional roadway and narrow roadway (to be used with appropriate forklift).

1) To meet the larger load demand, the maximum height can reach 16M.

2) Adjust the position of the beam with a pitch of 75 to better meet the requirements of stored goods.

3) If any parts are damaged in use, they can be easily replaced.

4) The surface of the shelf is treated and has high corrosion resistance.

5) can choose more abundant accessories and safety accessories.

6) Assembled shelf structure, easy to install and fast.

7) The component part uses high-quality materials, the welding is firm, and the installation is tight.

8) perfect accessories system, suitable for all kinds of special requirements.?

Structure: Main and auxiliary parts, columns, diagonal braces, cross braces, corner guards, beams, if necessary, install support frames and other components according to the shape of the goods.

5. Drive-in shelf:

Drive-in shelves are also called through shelves or corridor shelves. It is a continuous integral shelf that is not divided by channels. On the bracket shelf, the pallet is accessed in the depth direction, which makes the storage density of the drive-in shelf high, and the goods enter and exit from the same side of the shelf. Forklift can conveniently drive into the middle of the shelf to access the goods. The investment cost of the drive-in shelf is low, and it is suitable for the cases with large horizontal size, small variety and large quantity. Because of its high storage density and high utilization rate of ground space, it is often used in places with high cost of access space such as cold storage.?

1) High access density and poor access.

2) Applicable to the storage of less samples and more items.

3) Height up to 10M.

4) Access to items is limited by the order of storage, not easy to do first-in, first-out.

5) Not suitable for too long and too heavy items.

Structure: Brace, cross brace, diagonal brace, beam, guide rail, bollard, column,

6. Cantilever beam shelf:

The column is equipped with an outer suspension rod arm, which is suitable for storing long items such as steel pipe, section steel or plate. When placing round items, install a gear lever at the cantilever end to prevent the items from slipping off.?

1) only applies to strip or long roll goods storage.

2) Handling equipment with wide fork spacing is applicable.

3) The height is limited, generally below 6 meters.

4) The space utilization rate is low, generally around 35%-50%.

5) Suitable for building materials production factory, furniture manufacturer or supermarket.

Structure: cantilever, column, diagonal brace, cross brace.

7. Press-in shelf:

The press-in shelf is composed of guide rails, beams, upright posts and carrying trolleys. The rails are inclined and fixed on the beams at a certain angle. The carrying trolleys run on a strict track. The pallet goods are pushed in from the front, and the pallet goods are placed on the sliding seat. Later, the original ones will be pushed to the rear. At present, up to 5 pallets can be pushed in. The slide seat is on the slide rail, and the slide rail itself has a certain inclination, and the slide seat will automatically slide to the front entrance. The overall structure adopts the principle of "clip". The pallets are placed on the carrying trolley and pushed into the inside of the shelf in turn. The access mode is the same as that of the drive-in shelf, but the forklift does not need to drive into the shelf. As the depth direction of the shelf can be designed as multiple pallet positions, the space utilization of the press-in shelf is higher than that of the ordinary shelf. Safety and operation effect are higher than the drive-in shelf, widely used in cold storage, library, electronics and other industries.

1) high storage density, poor access, general depth of 3 storage bits.

2) The use of space compared with the beam shelf can save 1/3 and increase the storage density, but it is impossible to manage the goods first, first out.

3) Use general forklift access.

4) Suitable for small sample and large quantity items.

5) Not suitable for carrying heavy items.

6) The item will automatically slide to the front storage position.

8. Streamlined shelves:

By the flow bar, roller, column, beam, tie rod. This kind of shelf is also called roller type shelf, which is to send goods from one end to the other end through rollers. The goods slide by their own gravity, can achieve "first in, first out" operation. The use of low cost, access speed, high density. A roller-type aluminum alloy or sheet metal strip is set between each layer of beams of the shelf, which is placed at a certain slope. The goods are usually packed in paper or placed in plastic turnover boxes, and their own gravity is used to realize the flow and first-in-first-out of the goods. The goods are transported by trolleys, and are manually accessed and convenient to access. The load of each layer of unit shelves is usually about 1000KG, and the height of the shelves is within 2.5M. It is suitable for process conversion on both sides of assembly lines, sorting operations in distribution centers and other places. Information management of goods can be equipped with electronic labels. Widely used in supermarkets, pharmaceutical, chemical and electronic industries.

1) The flow type is to place the goods on the roller, using one side of the channel inventory, the other side to the goods.

2) The shelf tilts downward in the direction of shipment, and the goods slide under the action of gravity.

3) can achieve first-in, first-out, and to achieve a replenishment of multiple picking.

4) The storage efficiency of the streamlined shelf is high, which is suitable for short-term storage and picking of large quantities of goods.

5) This total shelf is widely used in logistics centers, freight lines, publishing houses and factories with high degree of automation.

9. Gravity shelf:

Gravity shelves use one side of the roadway as storage and one side of the roadway as access. The drum line is inclined and fixed on the beam at a certain angle. The tray is lowered from a high place and slides down along the direction of the drum line by its own gravity. In order to control the tray and stable slide down and avoid collision, a damping system is set at intervals on the drum line. The faster the tray slides down, the greater the resistance generated by the damping system. The end separating mechanism is provided at the lower end for separating two adjacent trays at the lowermost end, so that the lowermost end tray can be taken out smoothly. Gravity shelves have relatively high requirements for pallets. At present, the use of wooden pallets is relatively mature. Pallets made of other materials need to provide pallets actually used for damping experiments. The utilization rate of gravity-type shelves is higher than that of press-in type and drive-in type. Moreover, the principle of "first in, first out" is being realized. The safety and operation effect are the same as that of the beam shelf. The storage density is very good, but the cost is very high, which is suitable for the application of less samples and more high frequency.

1) use a large number of storage and to ship in a short time.

2) Suitable for Class B goods in the ABC classification.

3) Use first in first out.

4) Use dense runners to store stacks, with a space utilization rate of up to 85% 8) High construction costs and slow construction.

5) Use general forklift access.

6) The height is limited, generally below 6 meters.

7) Each channel generally stores only one kind of goods.

Structure: consists of drum line, drum, column, beam, tie rod, limit device, separation device, guide guard plate and guardrail.

10. Drawer type shelf:

Also known as mold shelves, it consists of columns. Drawer layer, pull rod, self-locking device, bearing, slide. This kind of shelf is suitable for storing various molds. The top can be equipped with a chain block and a horizontal moving trolley to facilitate the lifting of the mold. The drawer layer can be removed by 2/3. The drawer layer is mainly composed of slides, laminates and bearings. The laminate is composed of a force frame and a steel plate. Each slideway is fixed up and down by two bearings. It can roll freely in the guide groove with low resistance. It can easily pull out the drawer with one hand, reducing labor intensity. The self-locking device is composed of a positioning spring and a pin shaft, which ensures that the drawer cannot be moved after it is in place, and does not affect the operation of the drawer within the stroke range.

1) Assembled by a variety of combined parts, simple structure, easy to disassemble, transport and assemble

2) A roller track is arranged under the drawer board, which can still be pulled freely with a small force after bearing and slide smoothly.

3) Additional positioning safety device, safe and reliable, can be pulled out by 66%, each layer can store 500-2000KG. Such as mechanical processing equipment storage, is an indispensable modern factory storage supplies.

4) The drawer-type shelf covers a small area, has a large load-bearing capacity, detailed classification and easy operation.

5) It is used to store the mold without forklift. The top is equipped with a chain block mobile truck, which can realize the lifting of the mold. Widely used in molds.

11. Steel platform:

The structure consists of columns, main and secondary beams, floor surfaces, stairs and guardrails. Integral assembly, without field welding. Generally, the bearing capacity per square meter is 300-1000kg. The column adopts round tubes with strong bearing capacity and less rigidity. The primary and secondary beams can choose the most economical and reasonable H-type steel and the C- type cold-formed beam opened by our company in rigid structure engineering according to the bearing requirements. The floor panel adopts special C- type cold-formed patterned steel plate or hollow plate, adopts buckle plate structure, and is rigidly fixed with the primary and secondary beams. The overall structure of the whole platform is strong, according to the actual needs to choose different German floor panels to meet the fire or dust, anti-small falling requirements. The lighting system can be configured under the floor as required. Cargo can be transported by hydraulic lifting platform, freight ladder or forklift. All materials are made of high-quality carbon structural steel, automatic surface spray treatment, strong bearing capacity, simple and generous appearance, application of various industries.

12, attic shelf

Loft shelf is the factory floor area is limited, the use of steel beams and metal plates to the original storage area U floor distinction, each floor can be placed different types and shelves, and the shelf structure has the role of supporting the upper floor.

1) Improve the storage height and increase the space utilization rate.

2) The upper layer is limited to the storage of light-weight goods and is not suitable for the walking of weight equipment.

13. Tool cabinet

1) High-quality plates and special surfaces can be suitable for different factory working environments.

2) The steel load rail stamped by a professional mold can make the drawer easily open under no-load and heavy pressure.

3) There is a partition in the drawer, which can freely separate the storage space.

4) Advanced central vertical lock. Ensure safe opening and management of drawers.

5) Special aluminum alloy drawer handle, easy to change labels, and beautiful and practical.

6) can freely choose to configure different drawers, fully meet the needs of each household.

7) Pad feet at the bottom of the cabinet to protect the cabinet from damage and facilitate handling by forklift. It is divided into monorail and double track: monorail bearing 100kg, can pull out 90% height series in 50-300? double track bearing 200kg, can pull out 100 height series in 75-400.

14. Storage cage:

1) Grid structure, light weight and high strength. Assembly, folding simple, can be stacked four layers, improve space utilization.

2) The bottom is reinforced with U-shaped steel to ensure the bearing capacity.

3) Cooperate with handling equipment and can be used in logistics links such as transportation, handling, loading and unloading, storage and storage.